Use https://seceonhelp.freshdesk.com/support/login to access updated Knowledge Base Articles, Submit Technical Support Tickets and Review Status of submitted support tickets.

Configuring sflow from HP Switches

HP ProCurve switches are currently designed so that sFlow is enabled remotely by an sFlow collector – the CCE.


Example HP ProCurve sFlow configuration:

The following example was published in the context of a switch that had at least 55 ports installed. For the sake of this example, the IP address was 15.29.16.93.


STEP 1: Set the destination IP (The IP of the collector station--Note that the IP Address is in hex but without the leading 0x):

setmib sFlowRcvrAddress.1 -o 0F1D105D

For reference, here is an IP to HEX converter:

http://www.kloth.net/services/iplocate.php


STEP 2: Set the traffic destination port number

Destination port  6343

setmib sFlowRcvrPort.1 -i 6343


STEP 3: Enable Receiver

setmib sFlowRcvrOwner.1 -D Name sFlowRcvrTimeout.1 -i 100000000


STEP 4: Set flow sampling rate

Port 53, sampling rate of 37:

setmib 1.3.6.1.4.1.14706.1.1.5.1.4.11.1.3.6.1.2.1.2.2.1.1.53.1 -i 37

Port 55, rate of 20:

setmib 1.3.6.1.4.1.14706.1.1.5.1.4.11.1.3.6.1.2.1.2.2.1.1.55.1 -i 20

Port 5, rate of 20:

setmib 1.3.6.1.4.1.14706.1.1.5.1.4.11.1.3.6.1.2.1.2.2.1.1.5.1 -i 20

 (Note: Some switches require a sample rate of at least 50)


STEP 5: Set Enable to True (1), Per Port

Port 53: setmib 1.3.6.1.4.1.14706.1.1.5.1.3.11.1.3.6.1.2.1.2.2.1.1.53.1 -i 1

Port 55: setmib 1.3.6.1.4.1.14706.1.1.5.1.3.11.1.3.6.1.2.1.2.2.1.1.55.1 -i 1

Port 5: setmib 1.3.6.1.4.1.14706.1.1.5.1.3.11.1.3.6.1.2.1.2.2.1.1.5.1 -i 1


STEP 6: Set the counter polling interval, Per Port

Interval of 8 seconds,

port 53: setmib 1.3.6.1.4.1.14706.1.1.6.1.4.11.1.3.6.1.2.1.2.2.1.1.53.1 -i 8

Interval of 7 seconds, port 55: setmib 1.3.6.1.4.1.14706.1.1.6.1.4.11.1.3.6.1.2.1.2.2.1.1.55.1 -i 7

Interval of 50 seconds, port 5: setmib 1.3.6.1.4.1.14706.1.1.6.1.4.11.1.3.6.1.2.1.2.2.1.1.5.1 -i 50

 

If needed:

Disabling: To kill all sampling and to release the receiver just set timeout to 0:

setmib sFlowRcvrTimeout.1 -i 0

Seceon Inc. All rights reserved. https://www.seceon.com